The stall is a long pause in a brisket’s internal temperature, and Texas A&M’s meat science group names evaporative cooling as the cause: moisture leaving the meat cools it about as fast as the smoker heats it. You beat it by planning for it, not by raising the heat. Smoke at 225 to 250°F, expect the climb to flatten for a while, and pull the brisket when a probe slides in like warm butter.

Why the Temperature Stops Rising

Cooks widely report that wrapping the brisket in foil or butcher paper shortens the stall, because the wrap holds moisture against the surface and slows evaporation. That is common practice rather than extension guidance, and the trade-off is a softer bark.

Plan the Clock

A common rule of thumb, not agency guidance: pounds x 1 to 1.5 hours = cook time, then add 1 to 2 hours of rest. A 12 lb brisket is 12 to 18 hours of cooking, with the stall eating part of that. If dinner is at 6 p.m. and you want a 2 hour rest, a 15 hour estimate means lighting the fire about 1 a.m. For pellet-specific fuel numbers, see how to smoke a brisket on a pellet grill.

ChoiceEffect on the stall (cooks’ reports)Bark
Ride it out, unwrappedLongest stallFirmest
Wrap in butcher paperShorter; paper lets some moisture escapeSofter than unwrapped
Wrap in foilShortest; traps the most moistureSoftest
Raise smoker above 300°FOutside the FSIS 225 to 300°F smoking rangeNot recommended

Steps

  1. Thaw the brisket fully in the refrigerator. USDA FSIS says to thaw meat fully before smoking.
  2. Hold smoker air at 225 to 250°F. FSIS gives 225 to 300°F as the smoking range. Use one probe in the meat and a second for the air.
  3. When the meat flattens out in the middle of the cook, leave it alone. Opening the lid lets heat and humidity out and stretches the stall.
  4. Wrap, or not, once the bark is set and holds its color when you press it.
  5. Start checking for tenderness near 195°F and finish by feel. Pitmasters commonly land between 195 and 205°F; that is cooking convention, not a safety number.
  6. Rest it wrapped in a towel for an hour or more before slicing.

Doneness Versus Safety

USDA FSIS lists whole cuts of beef at 145°F with a 3 minute rest. A brisket passes that number hours before it is edible. The higher range is about tenderness, not safety: Texas A&M’s meat science group says collagen needs a higher internal temperature, 185 to 195°F, to convert. Refrigerate leftovers within 2 hours of taking the meat off the smoker, per FSIS, and slice what you need as you go. Our guide to smoking thermometers covers the two-probe setup.

Common Mistakes

  • Cranking the heat at the stall. It shortens the cook but dries the meat, and it can push the smoker past the FSIS range.
  • Pulling the brisket at a fixed temperature instead of by feel.
  • Starting too late. Build in the rest; a hot brisket sliced right away loses juice.
  • Trusting a lid thermometer. Grate-level air can differ from the dome reading.

Where to Set Up

An overnight cook makes placement matter. Never use a grill indoors or in a garage, breezeway, carport, porch or under a surface that will burn (CPSC). Keep the smoker away from the house, deck rails and branches (NFPA), and keep children and pets back. For the carbon monoxide basics, see why you can’t grill indoors. Shopping for a first cooker? Start with best smokers for beginners.

FAQ

How long does the stall last?

It varies with the cut, the smoker’s humidity and whether you wrap, so we give no fixed number. Plan the clock with a buffer and rest the brisket in a towel if it finishes early.

Is a stalled brisket undercooked?

Check with a probe. A reading of 145°F or more has passed the USDA number for whole cuts of beef, but the brisket is not tender yet. Keep going until the probe slides in with little resistance.

Where does our advice come from?

Texas A&M’s meat science group and USDA FSIS, plus common barbecue practice where we say so. We research and compare, and we do not use or review the products ourselves; see how we choose.

Changelog: November 2026: first published.