For a NAS, the job of a UPS is to give the box a few minutes to shut down cleanly, not to keep it running for hours. A 1500 VA sine wave unit such as the CyberPower CP1500PFCLCD or the APC BR1500MS2 carries a NAS, a router, and a switch (about 55 W in the example below) with plenty of headroom. Confirm each model’s data connection against your NAS maker’s compatibility list so the NAS can trigger its own shutdown.
Quick Comparison
| Model | Rating | Output on battery | Battery-backed outlets | Battery | Best for |
|---|---|---|---|---|---|
| CyberPower CP1500PFCLCD | 1500 VA / 1000 W (listing) | Sine wave (listing) | 6 | Listing: 3-year warranty includes battery | Most NAS builds |
| APC BR1500MS2 | 1500 VA / 900 W | Pure sine wave (listing) | 6 of 10 | User-replaceable, APCRBC163 | Listed runtime figure, easy battery swap |
| CyberPower CP1000PFCLCD | 1000 VA / 600 W | Sine wave (listing) | Per listing | Listing: 3-year warranty | Small NAS and network gear |
| CyberPower CP1500AVRLCD3 | 1500 VA / 900 W | Simulated sine wave | 6 | Listing: 3-year warranty includes battery | Standard power supplies |
How We Chose
We started with 600 W or larger line-interactive units with a USB connection, then ranked them on output waveform, watt rating (not VA), battery access, and warranty. Specs come from listings and APC’s product page; the Yard & Grid Score comes from verified buyer ratings. CyberPower’s product pages would not load for us, so its figures are listing claims. We research and compare; we do not use or review the products ourselves. See how we choose.
Sizing: Watts, Not VA
The watt rating is the limit. Take an example load of a two-bay NAS at 30 W, a router at 15 W, and a switch at 10 W: 30 + 15 + 10 = 55 W. Measure yours with a plug-in watt meter, because drives spin up higher than they idle. Against a 600 W rating that is 55 / 600 = 9 percent, and against 900 W it is 6 percent. Keeping a UPS well below its rating is a common planning margin; it also helps runtime.
Runtime scales roughly with load but not in a straight line. APC’s listing gives 73 minutes at 100 W for the BR1500MS2. A rough scale to 55 W is 73 x 100 / 55 = about 133 minutes. Treat that as an upper estimate and use the maker’s runtime chart. A NAS needs only a few minutes to shut down, so what matters is that the UPS can signal it.
Shutdown, USB, and Sine Wave
- USB shutdown. Synology’s DSM help describes connecting a UPS to the NAS by USB, ticking Enable UPS support, and choosing USB UPS. You then set how long the NAS waits after a power failure. Synology notes that UPS power-off behavior varies by brand and model, so check your model against your NAS maker’s compatibility list.
- NUT. If your server runs Network UPS Tools, confirm the UPS driver for your model before you buy.
- Sine wave. Pure or sine wave output is the safer fit for power supplies with active PFC; APC’s listing says so, and the CyberPower PFC series is aimed at the same use. A simulated sine unit usually works for simple loads, but it is the weaker choice for a server you care about.
1. CyberPower CP1500PFCLCD
- 1500 VA / 1000 W sine wave, six battery-backed and six surge-only outlets, per the Amazon listing; some retailers show 900 W or 10 outlets, so check CyberPower’s datasheet.
- Automatic voltage regulation corrects minor swings without using the battery; free PowerPanel software.
- Listing: three-year warranty that includes the battery.
Best for: a NAS plus a mini PC and network gear.
Avoid if: you need a maker-published runtime chart in hand before buying; read CyberPower’s.
2. APC BR1500MS2
- 1500 VA / 900 W, 10 outlets, AVR, and ENERGY STAR per APC’s page; the listing says six are backed up and four surge-only.
- User-replaceable battery (APCRBC163); the listing states a three-year warranty and 73 minutes at 100 W.
- The listing says it uses pure sine wave output and has data-line protection for coax and Ethernet.
Best for: a home lab where battery swaps matter.
Avoid if: shelf depth is tight; it is about 15 inches deep per the listing.
3. CyberPower CP1000PFCLCD
- 1000 VA / 600 W sine wave, enough for the 55 W example with more than 10 times the headroom.
- Same PFC sine wave family and LCD as the CP1500 above.
Best for: a single NAS and router.
Avoid if: you plan to add a second server or a monitor.
4. CyberPower CP1500AVRLCD3
- 1500 VA / 900 W, simulated sine wave, per the listing.
- Six battery-backed outlets, AVR, and free PowerPanel Personal software.
Best for: a NAS with a standard power supply.
Avoid if: your server power supply is active PFC and the maker recommends sine wave.
Cost of Ownership
Sealed lead-acid batteries wear out; the APC listing shows 5 years of average life, and the CP1000PFCLCD and CP1500AVRLCD3 listings show 3 years. Budget for a replacement. Plug the UPS directly into the wall receptacle, and do not plug a surge protector, power strip, or extension cord into its output, as Schneider Electric (APC) advises for Back-UPS units. See how long a UPS lasts for the runtime math. Check each manual for any restriction on the equipment you connect.
How to Choose
- What is your load in watts? Add NAS, router, and switch, then keep it under about half the UPS watt rating.
- Does your NAS list the UPS? Check the compatibility list for USB shutdown.
- Will you add gear? A bigger unit costs more than a small one; leave room.
FAQ
Do I need a UPS for a NAS?
Not required, but a power cut mid-write is the main way a NAS gets corrupted, so a small UPS is cheap insurance. It does not replace backups.
Is a surge protector enough?
It handles spikes, not outages. See UPS vs surge protector.
Can I use a power station instead?
Some power stations have a UPS mode; check the switchover spec first. See UPS mode explained.
Changelog: November 2026: first published.