Reverse searing means cooking the roast low and slow first, resting it, then finishing over high heat. Run the cooker near 250°F until the center reads 110 to 115°F for medium rare, rest up to an hour, then sear at 450 to 500°F for 10 to 12 minutes. That sequence comes from a BarbecueBible.com recipe, a food blog, and it ends at 125 to 130°F. USDA FSIS puts whole beef at 145°F with a 3 minute rest, so decide before you start which finish you are cooking for.
Set Up Safely
- Run the grill or smoker outdoors only, well away from the house, deck railings, eaves and overhanging branches (NFPA).
- Never use a grill indoors or in a garage, breezeway, carport, porch or under a surface that will burn (CPSC).
- Set up two zones: a cool side for the slow stage and a hot side for the sear. Our two-zone fire guide shows the layout.
- Keep children and pets at least 3 feet from the cooker (NFPA).
The Method
| Stage | Heat | Stop when | Source |
|---|---|---|---|
| Slow roast | About 250°F, indirect | 110 to 115°F in the center (medium rare) | BarbecueBible.com recipe (blog) |
| Rest | Wire rack, loose foil tent | Up to 1 hour | BarbecueBible.com recipe (blog) |
| Sear | 450 to 500°F direct | 10 to 12 minutes, turning often, ends included | BarbecueBible.com recipe (blog) |
| Safe finish, whole beef | Any | 145°F measured, then 3 minute rest | USDA FSIS |
- Salt the roast ahead and keep it at 40°F or below until it goes on the cooker.
- Push a probe into the center of the thickest part, away from bone and fat.
- Roast indirect with the lid shut. Watch the probe, not the clock.
- Pull the roast at your target, rest it, then sear on the hot side. Watch for flare-ups from the dripping fat.
- Re-probe in two or three spots before you carve.
Plan the Clock
The blog recipe quotes 2 to 3 hours for the slow stage on a 3 to 4 bone cut, and about 4 to 5 hours total with rest and sear. Your pace will differ. Example only: a roast that gains 30°F an hour goes from 40°F to 115°F in (115 minus 40) / 30 = 2.5 hours. Add the rest and the sear, then a 30 minute buffer, and dinner is not waiting on the roast.
Which Finish Do You Want?
The 110 to 115°F pull is a doneness choice, and the 125 to 130°F finish is below the USDA minimum. If you want to follow USDA, keep roasting low until the probe reads 145°F at the center, then rest it and sear briefly for color. Confirm 145°F with the probe before the 3 minute rest starts. Our prime rib doneness guide lays out both options.
Prime Rib Steaks and the Oven
Slices cut from the roast, sold as prime rib steaks, follow the same order of low heat, rest, then a hard sear. They are thinner, so they reach every number sooner and the probe matters more. A home oven can handle the slow stage: set it low, probe the same way, and sear in a hot cast iron pan or on the grill outside. Never bring a charcoal or gas grill indoors for the sear.
Mistakes to Avoid
- Trusting a lid dial instead of a probe at the grate.
- Probing against bone, which can skew the reading.
- Searing straight off the cooker without a rest, which overshoots your target.
- Leaving the cooked roast out for hours. Refrigerate leftovers within 2 hours, or 1 hour above 90°F (USDA FSIS).
For the all-smoke version, read how to smoke a prime rib. Charcoal cooks can use reverse searing on a charcoal grill. Timing questions are covered in how long to rest prime rib, and probe options in wireless meat thermometers. See how we choose for our sourcing.
Changelog: November 2026: first published.