The EcoFlow Smart Home Panel is a smart subpanel, installed beside a home’s main electrical panel, that moves a chosen set of household circuits from the grid to EcoFlow batteries when the power fails, with a switchover EcoFlow rates at 20 milliseconds. It does not store or make any energy itself: it is the switching and control layer between your wiring and the EcoFlow power stations that hold the energy.

Why It Matters for a Homeowner

A portable power station on its own can only run what you plug into it with a cord. Hard-wired loads such as a well pump, a furnace blower, or a kitchen circuit have no plug, so they need transfer equipment between the battery and the house wiring. The Smart Home Panel is EcoFlow’s version of that equipment, with circuit-level control in the EcoFlow app added on top.

The Generations at a Glance

Three versions exist, and each one is tied to a different EcoFlow battery family. The figures below come from EcoFlow’s US product pages and EcoFlow’s own blog.

Spec (EcoFlow published)Smart Home Panel (first generation)Smart Home Panel 2Smart Home Panel 3
Backed-up circuitsUp to 101232
Battery familyDELTA Pro, plus Extra Batteries and Smart GeneratorsDELTA Pro Ultra (alone, or paired with DELTA Pro or the Double Voltage Hub), or DELTA Pro 3DELTA Pro Ultra X
Maximum system size2 DELTA Pro units; 3.6 to 25 kWh; up to 7,200 WUp to 3 inverters and 15 batteries; up to 90 kWh and 21.6 kWNot stated on the page we reviewed
Switchover20 ms20 ms automaticUnder 20 ms
Generator inputEcoFlow Smart GeneratorsPortable gas generators from 3 to 12 kWSplit-phase generator supported
EnclosureNot statedDistribution panel NEMA 3R (indoor or outdoor); battery connection box NEMA 1 (indoor)NEMA 3R

EcoFlow’s Smart Home Panel 2 page lists 90 kWh in one FAQ (DELTA Pro Ultra) and 25 kWh in another that describes 3,600 Wh DELTA Pro units, so the ceiling depends on which stations you connect; confirm it for your exact configuration with EcoFlow before you plan around it.

What It Does

  • Switches selected circuits to battery power during an outage and back to the grid when it returns.
  • Charges the connected batteries from the grid while utility power is on.
  • Sets circuit priority in the app, so lower-priority loads can be dropped to stretch runtime; the Smart Home Panel 2 offers three priority levels.
  • Runs energy modes on the Smart Home Panel 2, including Backup Reserve, Self-Power, scheduled tasks, time-of-use, and a storm mode that charges ahead of forecast severe weather.

What It Does Not Do

  • It does not add capacity. Runtime depends on the batteries connected, not the panel.
  • It does not back up circuits it is not wired to. Anything left on the main panel goes dark in an outage.
  • It does not sell power back. EcoFlow says the DELTA Pro Ultra cannot feed back to the grid, and the Smart Home Panel 2 cannot connect to NEM 2.0 rooftop solar systems.
  • It does not work with any battery brand, or with every EcoFlow station; each generation supports only the EcoFlow stations on its compatibility list.
  • It is not a do-it-yourself device. EcoFlow’s Smart Home Panel 2 page says installation is required before use and tells buyers to make sure the electrician is properly licensed.

Installation is a job for a licensed electrician, who sizes the equipment, pulls the local permit, and makes every connection. We do not give wiring steps for this or any panel work.

How Long a Backed-Up Home Runs

Start with the load. A Smart Home Panel 2 system with one DELTA Pro Ultra holds 6,144 Wh. With 0.85 as a common planning figure for inverter and conversion loss, and an essentials load that averages 500 W across the day (fridge cycling, furnace blower, lights, router), runtime is 6,144 Wh x 0.85 / 500 W = about 10 hours. Doubling the battery roughly doubles that; doubling the load cuts it in half. More scenarios are in how long a home battery backup lasts.

Smart Home Panel vs a Transfer Switch

A standard manual transfer switch does the same core job, moving chosen circuits between grid and a backup source, but it has no app, no charging role, and no automatic switchover. The Smart Home Panel bundles those functions for EcoFlow batteries only, while a transfer switch or interlock works with a generator from any brand. The concepts are in transfer switch basics.

If you are still choosing between battery systems, our whole home battery backup options guide compares EcoFlow against other home battery setups, and home battery backup vs generator covers the fuel side. If a generator joins the system, run it outdoors only, at least 20 ft from the home and far from windows, doors, and vents as the CPSC advises, with the exhaust pointed away from the home, and keep battery-powered or battery-backup carbon monoxide alarms on every level and outside sleeping areas.

Changelog: November 2026: first published.