With 200 W of solar panels, a 1,000 Wh power station needs about 6.7 peak sun hours to refill from empty: 1,000 Wh / (200 W x 0.75 real-world derate) = about 6.7 hours. In June that is roughly one to one and a half average days almost anywhere in the U.S. In December it stretches to about two to four days across much of the northern half of the country.

The clock on the wall is the wrong unit for this question. Solar charging is counted in peak sun hours, and the number of those you get per day changes more with the season and your latitude than with the brand of panel you buy. The tables below cover both halves of the math.

The Charge Time Formula

Charge time in peak sun hours = watt-hours to refill / (usable panel watts x 0.75). Divide that result by your local peak sun hours per day and you get days.

  • Watt-hours to refill: the battery’s rated capacity in watt-hours (Wh), the size of the tank, or only the part you drained. Refilling a station from 40 percent needs 60 percent of the rating.
  • Usable panel watts: the smaller of your panel rating and the station’s maximum solar input. Panel watts above that ceiling are clipped and add nothing to charge speed.
  • 0.75 derate: a common planning figure for portable panels, covering heat, imperfect angle, wiring, and conversion losses inside the station. The PVWatts model from the National Laboratory of the Rockies (formerly NREL) uses a default of 14 percent losses for typical fixed arrays; portable setups usually lose more.
  • Peak sun hours: the day’s solar energy expressed as hours of full-strength sun (1 kWh per square meter per day equals 1 peak sun hour).

Here is how the first half of the formula plays out for common battery and panel sizes. Each cell is battery Wh / (panel W x 0.75), assuming the station accepts the full panel wattage.

Battery to refill100 W of panels200 W400 W800 W
500 Wh6.7 sun hours3.31.70.8
1,000 Wh13.3 sun hours6.73.31.7
2,000 Wh26.7 sun hours13.36.73.3
3,000 Wh40.0 sun hours20.010.05.0

Our guide to how many watts of solar a power station needs runs the same formula backward, starting from the charge time you want.

Winter Sun Hours by City

December is the month to plan around, because it has the fewest peak sun hours and the most winter storm outages. The figures below are NASA POWER climatology averages for 2001 to 2025, for a south-facing surface tilted at the local latitude, alongside the same location with the panel lying flat.

CityDecember, tilted (sun hours/day)December, flatJune, tiltedWh per December day from 200 WDays to refill 1,000 Wh in December
Seattle, WA1.70.95.02553.9
Minneapolis, MN2.51.35.33752.7
Chicago, IL2.41.45.23602.8
Boston, MA2.71.55.04052.5
Atlanta, GA3.62.45.35401.9
Houston, TX3.62.75.55401.9
Denver, CO4.22.46.46301.6
Phoenix, AZ4.93.17.47351.4
Miami, FL4.63.65.06901.4

The Wh column is 200 W x 0.75 x December sun hours, and the last column is 1,000 Wh divided by that daily figure. These are monthly averages, so a run of overcast days can deliver far less, and a clear cold day can beat them.

Two patterns stand out. Tilt matters more in winter than in summer: in Chicago a panel propped toward the low December sun collects about 2.4 / 1.4 = 1.7 times what the same panel collects lying flat. And latitude matters more than climate reputation: Seattle’s December gives a 200 W panel about a third of what Phoenix’s does.

Worked Examples With Real Stations

The station’s own input limits decide how much of a big array it can use, so each example starts with the manufacturer’s numbers.

Jackery Explorer 1000 v2 in Chicago

Jackery rates the Explorer 1000 v2 at 1,070 Wh with up to 400 W of combined solar input across two ports. With one common 18 V, 200 W panel, the 10.5 A port limit holds input to about 18 V x 10.5 A = 189 W: 1,070 Wh / (189 W x 0.75) = about 7.5 peak sun hours. At Chicago’s December average of 2.4 sun hours a day, that is 7.5 / 2.4 = about 3 days. A second panel on the other port, about 378 W in total against the 400 W ceiling, cuts it to 1,070 / (378 x 0.75) = about 3.8 sun hours, or about 1.6 December days.

EcoFlow DELTA 3 Plus in Chicago

EcoFlow lists the DELTA 3 Plus at 1,024 Wh with two 500 W solar inputs, 1,000 W in total, and quotes a full solar charge in about 70 minutes under ideal input. Using the planning derate instead: 1,024 Wh / (1,000 W x 0.75) = about 1.4 peak sun hours, so a single December day in Chicago would refill it with sun to spare. The catch is carrying and aiming 1,000 W of portable panels, which is several large folding panels. EcoFlow’s 1,000 W figure is 2 x 500 W, and its manual limits total short-circuit current (Isc) across both inputs to 15 A, so a real array may deliver less.

BLUETTI AC180 in Atlanta

BLUETTI rates the AC180 at 1,152 Wh with a single 500 W solar input. With a full 500 W array: 1,152 Wh / (500 W x 0.75) = about 3.1 peak sun hours, which Atlanta’s December average of 3.6 covers in one day. With 200 W of panels it becomes 1,152 / 150 = about 7.7 sun hours, or roughly two days.

So what: a station’s solar input rating sets the floor on charge time. A 400 W ceiling cannot refill 1,000 Wh in one Chicago December day no matter how many panels you own, while a 1,000 W input can.

Subtract the Loads Running at the Same Time

During an outage the panels feed whatever is plugged in before the battery sees any surplus. A fridge whose yellow EnergyGuide label reads 525 kWh a year averages 525,000 Wh / 8,760 h = about 60 W, so it pulls 60 W x 24 h / 0.85 inverter efficiency = about 1,700 Wh a day from the battery. In Chicago in December, 400 W of panels deliver about 400 W x 0.75 x 2.4 = 720 Wh a day, so the station keeps losing ground. The panels slow the drain; they do not refill the tank. Our fridge runtime guide has the battery side of that budget.

What Makes Charging Slower Than the Math

  • Cold batteries. LiFePO4 stations generally refuse to charge below freezing; Jackery lists a 32°F to 113°F charging range for the Explorer 1000 v2. Keep the station indoors and run the cable outside to the panels.
  • Shade on part of a panel. A shadow across a few cells can drag down the whole panel, and with series wiring the whole string.
  • Low panel voltage. Each input has a minimum voltage and a current limit. One small panel may sit below the window or hit the amp cap before the watt cap.
  • The last few percent. Many stations slow the charge as the battery nears full, so the final stretch takes longer per watt-hour than the middle.
  • Flat panels in winter. As the city table shows, a panel lying flat in December collects a fraction of what a tilted one does.

Plan the Array for Your Worst Month

Size panels for the December number in your area, then confirm the station can accept that wattage at the voltage your panels produce. Our step-by-step guide on how to charge a power station with solar panels covers ports, voltage windows, and placement, and our roundup of the best solar panels for power stations compares panels by output, open-circuit voltage, and connector. For what the watt-hour rating on the box means in usable energy, see our watt-hour explainer.

Changelog: November 2026: first published.