Most Traeger error codes point to one of four parts: the temperature probe (RTD), the igniter, the auger, or heat that ran too low or too high. Match your code below, do the simple fix first, and call Traeger support if it comes back. Codes and meanings vary by controller and model year, so your model’s support page and manual decide when they differ from this list.
Code Lookup
| Code | What Traeger describes | First fix |
|---|---|---|
| LEr | Non-WiFIRE grills: temperature stayed low for 10 minutes and the grill shut down (about 125°F per Traeger’s support section; one older manual says 120°F) | Remove pellets from the fire pot, power-cycle the controller, restart |
| HEr | Non-WiFIRE grills with 3-digit controllers: temperature above 550°F; Traeger lists grease fires and poor maintenance as causes | Shut off, let it cool, clear pellets from the fire pot, clean grease, restart |
| Err / Er1 | Bad connection or disconnect between the RTD probe and the control panel (an older manual calls Er1 a bad probe) | Follow Traeger’s article for your controller; replace the probe if told to |
| Er2 | RTD probe failure per Traeger’s support article (an older manual lists a disconnected thermocouple) | Inspect the probe and cable; contact support if unsure |
| Er3 / Er5 | Igniter (hot rod) disconnected or failed to ignite; AC pellet grills | Follow Traeger’s connection check, or call support to replace the hot rod |
| Er6 | Auger disconnected; AC pellet grills | Follow Traeger’s connection check, or call support |
| Er7 | Auger jammed; AC pellet grills | Clear the jam using the routine in your manual |
Newer WiFIRE grills show a “!” and you press the dial to read the code. Their codes use a different format. Traeger’s support site lists ER01 as a high temperature error (above 550°F, most often a grease fire) and ER06 as a temperature sensor disconnected. We could not find “ERL” or “HotE” in Traeger’s documentation. “ERL” is most often a misreading of LEr, and a “hot” message points to the high-temperature family above. Check the manual.
Before Any Repair
- Turn the grill off, unplug it, and let it cool fully.
- Opening the controller or hopper area to check wiring is beyond this guide. Follow Traeger’s article for your model, or call support, which also handles replacement parts.
- Keep the lid and hopper closed if you see flames, and do not use water. If fire spreads, call 911.
Fixing Low Temperature (LEr)
A low reading for over 10 minutes means the fire never caught or died. Third-party guides and owners most often report these causes: ash packed in the fire pot, damp pellets, an empty hopper, wind, or cold air. An older Traeger manual says to remove the pellets from the fire pot, turn the controller off and on, and restart. See the cold weather guide.
Fixing High Temperature (HEr)
Traeger lists grease fires and poor maintenance among the causes. Shut the grill off and let it cool, then clear the fire pot and clean the grease path. See how to clean a pellet grill. Keep the grill clear of the house, as NFPA advises.
Probe, Igniter, and Auger Codes
- Err, Er1, Er2: Traeger describes a bad RTD connection (Err, Er1) or a failed probe (Er2). Look for a cut or pinched probe cable from the outside, then follow Traeger’s article for your controller. Owners report that a grease-coated probe can also read wrong, so wipe it when the grill is cold.
- Er3, Er5: Traeger says the igniter is disconnected. If its steps do not clear the code, the hot rod may need replacing through support.
- Er6, Er7: Er6 is a disconnected auger and Er7 is a jammed auger, on AC pellet grills. An older Traeger manual describes holding DOWN and IGNITE in idle to run the auger forward and back for 60 seconds.
Older manuals and third-party tables disagree with Traeger’s newer pages on some codes, including Er2, Er3, and Er4. Go by Traeger’s support page for your controller, not a forum chart.
When to Call Support
Call if the same code returns after you reseat the wires and clean the pot, or if the grill will not power up. If the grill loses wall power mid-cook, see running a pellet grill on a power station or generator. To see how a pellet grill fits together, read how pellet grills work.
Changelog: November 2026: first published.