Choose the panel to fit the station, not the other way around: copy four numbers from the station’s spec sheet (maximum solar watts, input voltage window, current limit, and plug type), then pick a panel whose open-circuit voltage sits inside that window with room to spare. For a typical 1,000 Wh station with a 12 to 60 V input, that points to one 200 W folding panel, two of them in series, or a single 400 W suitcase rated around 40 V, but never two of the 40 V panels in series.
Panel size comes second, and it should come from the load you want to carry, not from the biggest number the station accepts. Weight, fold size, and cable length decide whether you will actually set the panel out on the third day of an outage.
Step 1: Copy Four Numbers From the Station
Every station publishes a solar input spec, usually under “Solar Input” or “DC Input” in the manual. Write these down before you look at a single panel.
| Station number | What it limits | Example: Jackery Explorer 1000 v2 | Example: Anker SOLIX C1000 Gen 2 |
|---|---|---|---|
| Maximum solar watts | Panel watts above this are wasted | 400 W across two ports | 600 W |
| Voltage window | Panel or string Voc must stay below the top | 12 to 60 V | 11 to 60 V |
| Current limit | Amps above this are clipped | 8 A below 16 V; 10.5 A from 16 to 60 V, per port | 8.2 A from 11 to 28 V; 14.5 A from 29 to 60 V |
| Plug | Which adapter you need | DC8020 (8 mm) | XT60 type (Anker calls it XT60i) |
Figures are from Jackery’s and Anker’s product pages. The current column matters more than most buyers expect: a panel that sits in a station’s low-voltage band can be held to fewer watts than its label promises. Our best solar panels for power stations guide has the same four numbers for the EcoFlow DELTA 3 Plus and BLUETTI AC180.
Step 2: Size the Panel From the Load
Start with what must keep running, then divide by the sun you get in your worst month. The formula: panel watts = daily watt-hours from the battery / (peak sun hours x 0.75 real-world derate). Peak sun hours are the day’s sunlight expressed as hours of full-strength sun; 0.75 is a common planning figure for heat, angle, wiring, and conversion losses on portable panels.
Worked example: a 15.7 cu ft chest freezer. ENERGY STAR lists the GE FCM16DL at 277 kWh a year, so it uses 277,000 Wh / 365 days = about 759 Wh a day. Through an inverter at 0.85 efficiency, the battery supplies 759 / 0.85 = about 893 Wh a day.
- Chicago in December: the PVWatts calculator from the National Laboratory of the Rockies (formerly NREL) gives about 2.66 peak sun hours a day on a panel tilted at the local latitude (a typical-year average; real Decembers vary). 893 Wh / (2.66 x 0.75) = about 448 W of panels.
- Chicago in June: the same source gives about 5.43 sun hours. 893 Wh / (5.43 x 0.75) = about 219 W.
So what: a 200 W panel falls just short of that freezer even in a Chicago June (219 W needed) and covers only about 45 percent of its daily draw in December (200 / 448). If winter storms are your outage season, plan on 400 W or more, and check that the station accepts that much. For sizing from battery capacity instead of load, see how many watts of solar a power station needs.
Step 3: Pick a Form Factor by Watts per Pound
Folding panels trade some durability for weight; rigid glass panels trade carry weight for a frame you can bolt down. Dividing rated watts by weight and by open area puts the four common types on one scale.
| Panel (source) | Type | Rated W | Weight | Watts per lb | Notes |
|---|---|---|---|---|---|
| Renogy RSP200D (datasheet) | Rigid glass, aluminum frame | 200 | 26.5 lb | 200 / 26.5 = about 7.5 | 58.7 x 27.5 in, about 17.8 W per sq ft |
| Renogy 400W Lightweight Portable Solar Suitcase (Renogy page) | Folding suitcase with kickstand | 400 | 30.2 lb | 400 / 30.2 = about 13.2 | 111.8 x 33.7 in open, about 15.3 W per sq ft |
| Renogy 200W Portable (listing) | Folding panel | 200 | 13.9 lb | 200 / 13.9 = about 14.4 | Folds to about 24 x 23 in |
| Renogy 400W solar blanket RSP400SB (listing) | Folding blanket, 16 sections | 400 | 16.1 lb | 400 / 16.1 = about 24.8 | Retailer pages list heavier weights for older versions |
Watts per square foot is the open area divided into rated watts: 58.7 x 27.5 / 144 = about 11.2 sq ft for the rigid panel, so 200 / 11.2 = about 17.8 W per sq ft. Rigid glass is the heaviest per watt but the most compact per watt once it is set out. A blanket is the lightest to carry, which matters if the panel lives in a closet and comes out only when the grid goes down. A suitcase with a built-in stand is the easiest to aim at the sun, and aim is worth more in winter than any cell technology claim.
Step 4: Read the Electrical Label, Not the Listing
The label on the back of the panel lists four numbers, and the one that decides compatibility is Voc (open-circuit voltage, the voltage with nothing connected). Retail listings often scramble them. Two rules let you sort them out: Voc is always higher than Vmp (voltage at maximum power), and Isc (short-circuit current) is always higher than Imp (current at maximum power).
A real case: the Amazon listing for the Renogy 400W portable suitcase shows “Maximum Voltage 67.5 volts,” which would be over every 60 V window in the table above. Renogy’s own spec table for the same suitcase lists 47.2 V Voc, 40 V and 10 A at maximum power, and 11 A short-circuit current. One suitcase fits a 60 V input with about 12.8 V to spare. Two in series would be 2 x 47.2 V = 94.4 V, far over the limit, so a second suitcase needs its own input or a parallel connection the station’s current rating can handle.
Cold, clear mornings push Voc above the label figure, so leave a margin below the station’s maximum. Our solar panel roundup works through that cold-weather correction for a two-panel series string. How the station turns the panel’s voltage and current into charge is covered in our MPPT charge controller explainer.
Step 5: Match the Plug and Keep the Cable Short
Most panels end in MC4 connectors, so you need a lead from MC4 to the station’s plug: DC8020 for the Jackery Explorer 1000 v2, an XT60-type plug for the EcoFlow DELTA 3 Plus and Anker SOLIX C1000 Gen 2, DC7909 for the BLUETTI AC180. Check what is in the box; the Amazon listings for the Renogy portable panels above say MC4 output only, with the adapter sold separately.
An extension cable lets the station stay indoors while the panel sits in sun, but every foot costs a little power. The voltage drop is round-trip length x wire resistance x current. Using the NEC Chapter 9 resistance for stranded copper at 75°C, 1.98 ohms per 1,000 ft for 12 AWG and 1.24 for 10 AWG, a 25 ft extension is 50 ft of wire round trip:
- One 200 W panel at 18.8 V and 10.6 A (Renogy 200W Portable figures), 12 AWG: 50 x 0.00198 x 10.6 = about 1.05 V lost, or 1.05 / 18.8 = about 5.6 percent, roughly 11 W.
- Same panel, 10 AWG: 50 x 0.00124 x 10.6 = about 0.66 V, or about 3.5 percent.
- One 400 W suitcase at 40 V and 10 A, 12 AWG: 50 x 0.00198 x 10 = about 0.99 V, or 0.99 / 40 = about 2.5 percent.
So what: the same cable wastes about twice the share of a 20 V panel’s output as it does on a 40 V panel, because the higher-voltage panel moves its watts at the same current. If the station has to sit far from the sunny spot, a higher-voltage panel or a heavier-gauge cable gets more of the harvest to the battery.
Common Mistakes
- Buying watts the station cannot take. A 400 W panel on a 200 W input charges at 200 W at best.
- Trusting the “maximum voltage” field on a listing. Confirm Voc on the maker’s spec table or the panel label.
- Ignoring the low-voltage current band. On stations with a split current rating, a single 20 V panel can be held below its rating.
- Sizing for June. The freezer example needed about twice the panel in December.
- Forgetting the adapter. An MC4-only panel cannot charge anything until you have the station-specific lead.
Once the panel is chosen, our step-by-step guide to charging a power station with solar panels covers placement and first connection, and how many watts a solar panel produces explains why the station’s display rarely shows the full rating.
Changelog: November 2026: first published.