An interlock kit lets a portable generator feed your whole electrical panel while you choose which breakers stay on, and a manual transfer switch feeds a fixed set of circuits picked in advance; both keep generator power off the utility lines, and both are jobs for a licensed electrician under a permit.

This page compares the two as concepts so you can have a clear conversation with an electrician. It does not describe how to wire either one. Rules vary by town, by utility, and by which edition of the National Electrical Code (NEC) your area has adopted.

What Each One Is

An interlock kit is a mechanical plate or slide on the front of the main panel. It physically blocks the main breaker and a dedicated generator breaker from being on at the same time, so the panel takes power from one source or the other. A manual transfer switch is a separate small panel beside the main one, holding switches for the circuits you selected; each switch flips its circuit between utility and generator. Both usually pair with an outdoor power inlet box where the generator cord plugs in.

Interlock kitManual transfer switch
Where it sitsOn the main panel coverSeparate box next to the main panel
Circuits available on generatorAny breaker in the panelOnly the circuits wired to it
Who manages the loadYou, by turning breakers on and offSet by the circuits chosen at installation
Listing standardPanelboard accessory under UL 67, identified for a specific panelTransfer equipment under UL 1008
Code basisAccepted as transfer equipment under NEC 702.5 when identified for that panel, per the IAEITransfer equipment under NEC 702.5
Panel compatibilityMust match the panel’s make and modelWorks with most panels
SwitchingManualManual (automatic versions exist for standby systems)

Our transfer switch basics page explains backfeed, the hazard both devices exist to prevent, and our interlock kit explainer goes deeper on that device alone.

Four Differences That Matter

1. Which Circuits You Can Reach

With an interlock, every breaker in the panel can run on the generator, including circuits you did not think to plan for, such as a garage freezer or a bathroom outlet. With a manual transfer switch, only the circuits wired to it are available. Adding one later means another visit from the electrician.

2. Who Keeps the Generator From Overloading

Start with the load. The generator’s inlet sets a ceiling: a 30 A, 240 V inlet carries at most 30 A x 240 V = 7,200 W, and a 50 A, 240 V inlet carries 50 A x 240 V = 12,000 W. The generator’s own running watts may be lower still.

With an interlock, staying under that ceiling is your job during every outage. Say your generator runs 7,500 W. A fridge at 700 W, a furnace blower at 600 W, a 240 V well pump at 1,500 W, and lights at 300 W total 3,100 W, leaving 7,500 W minus 3,100 W = 4,400 W of headroom. Turn on a 4,500 W electric water heater breaker by habit and the generator overloads. A transfer switch limits you to the circuits chosen with the electrician, which makes that mistake harder to make. Figures here are planning examples; use the running and starting watts on your own nameplates, as shown in our running watts vs starting watts guide.

3. Whether Your Panel Has an Option

An interlock must be identified for your specific panel, and the panel needs room for the generator breaker in the position the kit requires. Older or less common panels may have no matching kit. A transfer switch sits outside the panel, so it is less dependent on what brand of panel you own. Whether a given kit is accepted is also up to your local inspector, which is a question your electrician can answer before any work starts.

4. Cost Drivers

An interlock is usually the smaller hardware purchase, since it is a plate plus a breaker, while a manual transfer switch includes its own enclosure and switches and takes more wiring time. In both cases, the inlet box, the cable run to where the generator sits, the permit, and the electrician’s labor often make up a large share of the total. Ask for a quote on both approaches; the gap depends on your panel and on how far the inlet is from it.

A Word on the Generator Itself

Neither device changes the carbon monoxide hazard of a fuel-burning generator. Run a portable generator outdoors only, at least 20 feet from the home, far from windows, doors, and vents, with the exhaust pointed away from the home, per CPSC guidance, and keep working CO alarms on every level and outside sleeping areas. Follow the generator manual and your local rules. The inlet box exists partly so the generator can stay out there while the power comes in.

Choose an Interlock Kit if

  • A listed kit exists for your exact panel and your inspector accepts it.
  • You want flexibility to power any circuit, and you are comfortable managing breakers during an outage.
  • You want the simplest hardware and the fewest new boxes on the wall.

Choose a Transfer Switch if

  • Your panel has no matching interlock kit, or the inspector prefers separate transfer equipment.
  • Someone else in the household may run the generator and you want the load limited by design.
  • Your list of essential circuits is short and will not change.
  • You may later move to a standby generator or a home battery, where automatic transfer equipment is standard.

Look elsewhere if your backup is a home battery system; those come with their own transfer equipment, covered in our whole home battery backup comparison. And if you only need a fridge and a few lamps, heavy-duty outdoor extension cords from a portable generator, per CPSC guidance, avoid panel work entirely.

FAQ

According to the IAEI, a panelboard interlock identified for use with that panel is treated as transfer equipment under NEC 702.5. Local adoption and inspector judgment still decide; your electrician will know the local position.

Can I put in an interlock kit myself?

Work inside a main panel involves live service conductors that the main breaker does not de-energize. Hire a licensed electrician, pull the permit, and have it inspected.

What size generator pairs with each?

The same sizing math applies to both: total the running watts of what you want on, add the largest starting surge, and match the inlet and cord rating. Our list of the best inverter generators for home use notes which models offer a 240 V outlet.

Changelog: November 2026: first published.