A dehumidifier’s pint rating is the amount of water, in pints per 24 hours, that the unit removes under a fixed set of conditions set by the Department of Energy (DOE), and since the rule change of June 2019 those conditions are 65°F and 60 percent relative humidity for portable units instead of the older 80°F. Cooler air holds less moisture, so the same machine now carries a smaller number: ENERGY STAR maps an old 50 pint rating to about 30 pints under the current method.
Why the number changed
The DOE moved the rating point closer to real basement conditions. Under the current federal procedure (10 CFR 430, appendix X1), portable dehumidifiers are rated at 65°F dry bulb and 60 percent relative humidity, and whole-home units at 73°F and 60 percent. ENERGY STAR describes this as a 15°F drop for portable units and says the lower-rated models began showing up in early 2020.
For a homeowner, the change matters most when replacing an older unit or reading older advice. A guide written before 2020 that recommends “a 70 pint unit for a wet basement” is describing a machine that today’s labels call roughly 40 to 50 pints, depending on the model.
Old vs new ratings
ENERGY STAR publishes an approximate conversion. The ratio is close to 0.6 across the portable range: 30 / 50 = 0.6, and 35 / 60 = about 0.58.
| Portable, old rating (80°F) | Portable, current rating (65°F) | Whole-home, old rating | Whole-home, current rating |
|---|---|---|---|
| 30 pints/day | 20 | 80 | 70 |
| 40 | 25 | 100 | 85 |
| 50 | 30 | 120 | 100 |
| 55 | 30 to 35 | 140 | 115 |
| 60 | 35 | 160 | 135 |
| 70 | 40 to 45 | 200 | 170 |
| 90 | 55 |
Source: ENERGY STAR dehumidifier capacity guidance, which calls the correlation rough and says actual changes vary by model. Some manufacturers publish their own pairings (Whynter, for one, lists its old 70 pint class as 50 pints under the current method), so compare the current rating on the spec sheet whenever you can.
What a pint rating means in buckets and kilowatt-hours
There are 8 pints in a gallon, so a 35 pint unit running at its rated conditions removes 35 / 8 = about 4.4 gallons a day. If its bucket holds less than that, you will empty it more than once a day unless you use a drain hose or a pump.
Efficiency is the second number on the label: the integrated energy factor (IEF), in liters of water removed per kilowatt-hour. Since June 13, 2019, federal minimums for portable units are 1.30 L/kWh up to 25 pints, 1.60 L/kWh from 25.01 to 50 pints, and 2.80 L/kWh above 50 pints. For a 35 pint unit at the 1.60 minimum: 35 pints x 0.473 liters per pint = about 16.6 liters, and 16.6 / 1.60 = about 10.4 kWh to remove that full amount. A model with a higher IEF uses proportionally less, and ENERGY STAR says certified models use about 20 percent less energy than conventional units removing the same moisture.
Pint rating vs coverage area
The pint rating is a measured figure under federal rules; the square footage on the box is the manufacturer’s estimate. Two units with the same pint rating can claim different coverage. ENERGY STAR’s sizing guidance starts from how damp the space is, then room size, and it advises that oversizing is better than undersizing. A basement that smells musty is in a different class from one with water on the floor after rain.
Real basements also run cooler than 65°F for part of the year, and any compressor unit removes less water in colder air than its rating shows. Check the low-temperature operating limit in the manual if your basement drops into the 50s.
To find the target humidity for your space, read ideal basement humidity level. For current-rating comparisons of specific models, see our guide to dehumidifiers for basements, and if moisture is coming from a leak rather than damp air, start with where to put water leak detectors.
Changelog: November 2026: first published.