A HEPA filter catches far more of the smallest particles per pass than a MERV 13 filter does, but a MERV 13 furnace filter is the upgrade most homes can make without a new machine. EPA lists HEPA at 99.97% or better for 0.3 micron particles and MERV 13 at 50% or better for particles from 0.3 to 1.0 micron. Pick MERV 13 for the central system and HEPA for a single room, and use both if smoke or dust is a recurring problem. We research and compare agency documents and maker pages, as our how we choose page explains. No product cards here, because our product data has no filter with a published spec for this comparison.
Side by Side
| MERV 13 | HEPA | |
|---|---|---|
| 0.3 to 1.0 micron | 50% or better | 99.97% or better, at 0.3 micron |
| 1.0 to 3.0 micron | 85% or better | Higher still, per EPA (smaller and larger particles are caught at higher efficiency) |
| 3.0 to 10.0 micron | 90% or better | Higher still |
| Rating system | ASHRAE MERV scale | Separate; EPA says HEPA figures are not based on MERV |
| Where it lives | Furnace or HVAC filter slot | Portable air cleaner, usually one room |
| Limit | Works only while the system blower runs; your fan and filter slot must handle it | One room per unit |
What Separates Them
1. The smallest particles
In a single pass, up to half of the 0.3 to 1.0 micron particles can slip through a filter that only meets the MERV 13 minimum, versus at most 0.03% for HEPA at 0.3 micron. Real MERV 13 filters can exceed the minimum, so the table shows floors, not typical results. For particles of 3 microns and up, both do well.
2. Where the air flows
EPA says portable air cleaners filter a single room, while furnace filters work only when the system is operating. A whole-house filter covers every room only during blower run time, and a bedroom unit covers one room for as long as you leave it on. Size a portable unit with air changes per hour = CADR x 60 / room volume: a CADR of 150 cfm in a 1,440 cu ft room (12 x 15 ft, 8 ft ceiling) gives 150 x 60 / 1,440 = 6.25 per hour. The 150 is an example, so read the label of the unit you are considering.
3. What your system can handle
EPA advises at least MERV 13, or as high as your system fan and filter slot can accommodate, and suggests an HVAC technician if you are unsure. A denser filter resists airflow more, so do not force a thick filter into a slot built for a thin one. Replace on the maker’s schedule, because EPA says an overloaded filter will not work well.
4. MERV 13 against MERV 11
EPA’s table gives MERV 11 at 20% or better for 0.3 to 1.0 micron, 65% for 1.0 to 3.0, and 85% for 3.0 to 10.0. MERV 13 raises those floors to 50%, 85%, and 90%. The jump is biggest for the smallest particles. Check your system’s limits before the upgrade.
Choose MERV 13 If / Choose HEPA If
- Choose MERV 13 if your furnace or air handler can take it and you want every room covered.
- Choose HEPA if you want to clean one room, such as a bedroom, and can size the unit by CADR.
- Avoid if your system manual caps you below MERV 13: HEPA in the room is then the better route.
- Use both when you want the central filter for the whole house and a portable unit where you spend the most time.
For the simpler habits that come first, see our indoor air quality in winter guide. Neither filter removes gases or moisture, and EPA says filtration does not replace source control and ventilation.
FAQ
Is a MERV 13 filter the same as HEPA?
No. EPA describes HEPA as a separate standard with 99.97% or better at 0.3 micron, and says its efficiency figures are not based on the MERV system.
Will MERV 13 harm my furnace?
EPA does not say it harms a furnace. It says to pick at least MERV 13, or the highest rating your fan and filter slot can accommodate, so a system that cannot move enough air through a dense filter may call for a lower rating. Ask an HVAC technician or read the furnace manual.
Should I buy an air cleaner that makes ozone?
No. EPA advises avoiding portable air cleaners and furnace filters that intentionally produce ozone.
Changelog: November 2026: first published.