Every home with a fuel-burning appliance, a fireplace, or an attached garage needs both alarms, because a smoke detector senses particles from fire and a carbon monoxide (CO) detector senses an odorless gas, and neither one does the other’s job unless its label says combination smoke and CO. So the real decision is placement: where a combination unit can cover both jobs, and where a single-purpose alarm still makes more sense.
Side by side
| Smoke alarm | CO alarm | |
|---|---|---|
| Senses | Smoke particles from flaming or smoldering fires | Carbon monoxide gas from burning fuel |
| Safety standard | UL 217 | UL 2034 |
| Where NFPA guidance places it | Inside each bedroom, outside each sleeping area, and on every level including the basement | In a central spot outside each separate sleeping area, on every level, and where local code requires |
| Mounting | Ceiling or high on a wall, per the manual | Wall, ceiling, or plug-in outlet, per the manual |
| Kitchen | Manufacturers commonly advise at least 10 ft from cooking appliances | CPSC does not recommend kitchens or spots above fuel-burning appliances |
| Replace | 10 years after the date of manufacture, per NFPA | At the end-of-life signal or the maker’s replacement date; Kidde rates its current CO alarms at 10 years |
| Detects natural gas | No | No |
The four differences that matter
1. What each one senses
A smoke alarm reacts to particles in the air. NFPA describes two sensing types: ionization alarms tend to respond faster to flaming fires and photoelectric alarms to smoldering ones, and NFPA recommends using both types or a dual-sensor unit. A CO alarm uses a gas sensor and stays silent in a smoky room with no CO.
Neither is a gas leak detector. A CO alarm does not respond to natural gas (methane) or propane. Kidde sells separate explosive gas and CO combination alarms, such as the plug-in COPDLG, which it says alerts to natural gas, propane, and CO in one unit. If the secondary question is “CO detector vs gas detector,” the answer is that they sense different hazards, and a home on natural gas or propane can reasonably have both.
2. How fast each one sounds
A smoke alarm sounds once enough smoke reaches its chamber. A CO alarm is built to weigh concentration against time, because CO harm builds with exposure. Kidde lists the UL 2034 response windows on its CO alarms:
| CO level | Alarm must sound within |
|---|---|
| 70 ppm | 60 to 240 minutes |
| 150 ppm | 10 to 50 minutes |
| 400 ppm | 4 to 15 minutes |
Read the table as a dose. At 70 ppm the window is 60 to 240 minutes; at 400 ppm the alarm must sound within 4 to 15 minutes. That design keeps brief, low readings from a gas range from causing nuisance alarms, and it is why a CO alarm that stays quiet does not mean zero CO in the room. Our explainer on what level of carbon monoxide is dangerous covers the ppm scale.
3. Where each one goes, and how many you need
Smoke alarms go in more places than CO alarms, because NFPA guidance puts one inside every bedroom. Count each list separately, then see where a combination unit can serve both.
Example: a two-story house with a basement and three bedrooms off one upstairs hallway.
- Smoke alarms: 3 bedrooms + 1 upstairs hallway + 1 main floor + 1 basement = 6.
- CO alarms: 1 upstairs hallway + 1 main floor + 1 basement = 3.
- Separate units: 6 + 3 = 9 devices.
- With combination units: 3 combination alarms in the hallway, main floor, and basement + 3 smoke-only alarms in the bedrooms = 6 devices.
A one-level apartment with two bedrooms off a single hallway works the same way: smoke = 2 bedrooms + 1 hallway = 3; CO = 1 hallway. One combination unit in the hallway plus two smoke-only bedroom alarms covers it with 3 devices instead of 4. Local code can require more, so check it before you buy. Our guide on where to put a carbon monoxide detector covers the spots to avoid.
4. Lifespan and power
NFPA guidance says to replace smoke alarms 10 years after the manufacture date printed on the back. CO alarm sensors wear out on their own schedule, so the replacement date comes from the maker; Kidde says its CO alarms made since 2013 carry a 10-year life, with a few listed exceptions. Combination units go by whichever limit comes first. Our page on how long carbon monoxide detectors last explains the end-of-life chirp.
Power source decides what still works in an outage. The CPSC advises battery-operated or battery-backup CO alarms, and hardwired smoke alarms normally carry a backup battery too. A plug-in CO alarm with no battery goes dark exactly when a generator or a camp stove is most likely to be running; our guide to carbon monoxide safety during power outages covers that risk.
Which to buy first
The goal is full coverage of both. If you are filling gaps one purchase at a time, start where the home is missing protection.
Choose a CO detector first if
- Your smoke alarms are already in every bedroom and on every level, but the home has no CO alarm.
- You have a gas furnace, gas water heater, gas range, fireplace, or an attached garage.
- You plan to run a portable generator during outages.
- Your current CO alarm is past its end-of-life date or chirping.
Choose a smoke detector first if
- Any bedroom, hallway, or level is missing a smoke alarm.
- Your smoke alarms are more than 10 years past their manufacture date.
- The home is all-electric with no attached garage and already has CO alarms for outage use.
Choose a combination unit if
The spot needs both alarms by the guidance above: the hallway outside bedrooms and each level are the usual places. A combination unit is not the right fit inside a bedroom that only needs smoke coverage, or anywhere close to a kitchen, where CPSC advises against CO alarms and smoke alarms need distance from cooking. Our guides to smoke and carbon monoxide detectors and CO-only detectors compare models.
FAQ
Can a smoke detector detect carbon monoxide?
No. A smoke-only alarm has no CO sensor. Only a unit labeled as a combination smoke and CO alarm, listed to both UL 217 and UL 2034, covers both.
Does a CO detector detect a gas leak?
No. CO alarms sense carbon monoxide only. For natural gas or propane, look for an alarm that lists explosive gas detection, and follow its manual for mounting height, since natural gas rises and propane settles low.
Do I need a CO alarm in an all-electric home?
Many state and local codes tie CO alarm requirements to fuel-burning appliances or an attached garage, so check yours. Outage habits still matter: a generator placed too close to the house can push CO indoors, which is why the CPSC recommends CO alarms on every level and outside sleeping areas.
Should alarms be interconnected?
The CPSC says interconnected CO alarms are best, so that when one sounds, they all sound. Many smoke and combination alarms offer wired or wireless interconnection; new hardwired alarms should go in through a licensed electrician.
Changelog: November 2026: first published.