Buy a portable (folding) panel if the station moves and you will set the panel out only during an outage; buy rigid panels if the array stays put all year. Per watt, the folding panel is about half the weight: 13.89 / 200 W = 0.07 lb per watt for the Renogy 200W portable, against 14.1 / 100 W = 0.14 lb per watt for a Renogy 100W rigid panel.
Specs Side by Side
Portable figures are from Renogy’s spec table for its 13.89 lb 200 W panel and Anker’s PS200 Bifacial page. Rigid figures are from Renogy’s spec page for its 100W 12V monocrystalline panel (black frame, RSP100D-BK); Renogy sells several 100 W variants, so confirm the exact model you buy.
| Spec | Folding: Renogy 200W | Folding: Anker SOLIX PS200 Bifacial | Rigid: Renogy 100W 12V |
|---|---|---|---|
| Weight | 13.89 lb | 10.6 lb | 14.1 lb (6.4 kg) |
| Lb per watt | 0.07 | 0.05 | 0.14 |
| Size | Folded: 23.72 x 22.99 x 1.97 in | Open: 54.2 x 31.2 x 0.7 in | 41.8 x 20.9 x 1.38 in |
| Open area per 100 W | Not stated | About 5.9 sq ft | About 6.1 sq ft |
| Voc / Vmp | 21.6 V / 18.8 V | Not stated (48 V, 4.16 A output) | 24.3 V / 20.4 V |
| Warranty | Not stated | 5 years | Varies by market: 25 years on output; 5 to 10 years on materials and workmanship |
The Differences That Matter
Weight and Footprint
Open area is a wash: Anker’s PS200 is 54.2 x 31.2 in / 144 = 11.7 sq ft for 200 W, or 5.9 sq ft per 100 W, against 41.8 x 20.9 in / 144 = 6.1 sq ft per 100 W for the rigid panel. The gap is in weight and in what happens when you put it away. A folding panel stores in a closet; a rigid panel stays where you mount it.
Voltage and Your Station
Voltage decides whether the panel works at all. Using the rigid panel’s Voc of 24.3 V and a 0.3 percent per °C planning coefficient, a 14°F morning (35°C below the 77°F rating point) lifts it to 24.3 x (1 + 0.003 x 35) = about 26.9 V. Two in series reach about 53.7 V, under a 60 V station limit; three reach about 80.6 V, over it. The same check applies to folding panels; see how to choose a solar panel for a power station.
Current matters as much. On a station that allows 8.2 A in its 11 to 28 V band and 14.5 A in its 29 to 60 V band, as the Anker SOLIX C1000 Gen 2 does, two rigid panels in parallel are held to 8.2 A x 20.4 V = about 167 W. In series they run at 40.8 V and 4.91 A for about 200 W.
Durability and Permanence
Rigid panels use glass or a stiff frame, and Renogy lists a 25 year output warranty on its 100 W rigid panel. Folding panels trade that for portability and need weights or stakes in wind. If the panels would connect to a home’s electrical system rather than plug into a station, that is a job for a licensed electrician.
Daily Energy Is the Same per Watt
Neither type makes more power at equal watts. One 200 W array produces 200 W x 5 peak sun hours x 0.75 derate = about 750 Wh on a good day; the sun hours depend on tilt, which a fixed rigid mount sets once and folding kickstands let you adjust. Details are in how many watts a solar panel produces.
Choose Folding If or Rigid If
Choose portable if the station lives in a closet, you carry the panels to the yard or campsite, or you rent. Best for: outage-only use and travel. Avoid if: the panels will stay outside through every season.
Choose rigid if the array has a permanent spot and you want a long output warranty. Best for: a fixed yard or shed array feeding a station. Avoid if: you need to carry or store the panels.
We research and compare; we do not run our own product trials, as explained on how we choose. Panel picks are in the best solar panels for power stations and are portable solar panels worth it.
FAQ
Can I plug a rigid panel into a portable power station?
Yes, if the connector fits and the panel voltage and current stay inside the station’s solar limits. Compare Voc at your coldest temperature with the station’s maximum.
Do folding panels wear out faster?
Makers do not publish a comparable wear-rate figure, so we do not claim one. Compare warranty terms on the model you are considering.
Which charges faster?
At equal watts and equal sun, neither. Charge time is capacity / (panel watts x 0.75); see how long it takes to charge a power station with solar.
Changelog: November 2026: first published.